ARCMATE 100I PDF

CNC Manual/Fanuc Robotics/Fanuc Robot ARC Mate i MODEL B Maintenance Manual M-6i. Fanuc Robot ARC Mate i MODEL B Maintenance Manual. Refurbished Fanuc M-6i / Arcmate i with RJ2 control and pendant. Recommended applications: Material Handling, Press tending, CNC machine tending. Fanuc Arcmate i robots with RJ3 Control, Welding robots Comes Tested Available in Large Quantities All Of Our Robots Are Tested and in A Condition.

Author: Mezir Shakalmaran
Country: Oman
Language: English (Spanish)
Genre: Health and Food
Published (Last): 27 August 2006
Pages: 361
PDF File Size: 9.44 Mb
ePub File Size: 14.24 Mb
ISBN: 152-7-20132-193-3
Downloads: 48505
Price: Free* [*Free Regsitration Required]
Uploader: Bamuro

It cannot be reconfigured to listen to the serial port. RJ controller – has RSC 25pin on front. Thanks again for the help from forum members!

Started by zaneta30 on Fanuc Robot Forum. I do not yet have access to the CRC. I do NOT have K-floppy software. So I tried a couple pieces of software – Serial-to-Ethernet “Bridge” software.

Fanuc Arcmate 100i

In theory you 100j run any protocol over a serial port, but both sides need to do this, you cannot unilaterally decide to treat your serial port as a network device.

I have tried the following: Do you have access to the Fanuc CRC? It comes with Kfloppy. I am registered with Fanuc but waiting to hear back from them.

ERBU free demo version is all I need to make simple backups. I’m still hunting for a copy of Kfloppy so Arcmare can simplify the whole matter and get my two old RJs backed up. I found my old desktop with WinXP on it, and a serial port on the back.

  LEM CYBERIAD PDF

And welcome to the forum! I move the tip to the corner of the work piece using the pendant and save that point as a second position register.

Fanuc ARCMATE I R-J2 communication in Fanuc Robot Forum – Page 1 of 1

The extrusions are on a rotating fixture so that all the welds can be done. The left left corner tells when the question was posted.

The upper right tells the join date. Perhaps someone will chime in.

I have now copied and pasted the program so that it runs 4 times in one program, there is a pause programmed in for me to turn the fixture and mount the next part. The same software setup on my desktop allowed me to set it up as a “Client” to not only receive the signal via TCP, but then should make it accessible over the network – where the ERBU software will be looking for it. The serial port is a serial port, your network interface ardmate a network arcmage.

Fanuc ARCMATE 100I R-J2 communication

Advertisement Guest Advertisement Guest. Once the program starts it moves to a point on the fixture center punch mark which is in a different point for every orientation of the fixture, I just check that it lines up and start the next cycle.

  GA X46-033 PDF

I was of the understanding that the STE Bridge software would create this connection, which could then be picked up on the network – or better yet, on the server laptop itself. December 24, I am using a Fanuce Arcmate i with an Rj2 controller to weld ends on to long aluminium extrusions.

Fanuc Arcmate i progamming question. I haven’t been able to pull it off. I now find the difference between this position register and the originally programmed position and store this in a third position register. Hi guys, i’m having some problem with a r-j2 controller, it might be simple for some of you guys here but i’m kind of lost right now, i’ve been messing with it for a couple days so far and nothing seem to be working.

July 01, I have a laptop with RS 9pin on the back. November 05, I made up what I believe is the right custom cable.

It’s not just a matter of getting the signal to a network point of communication. Started by latendal on Fanuc Robot Forum.