HICOM 100E SERVICEHANDBUCH PDF

siemens hicom e service manual pdf – This list of telephone switches is a compilation of telephone switches used in the public switched telephone network . [EPUB] Siemens Hicom e Service Manual [PDF]. Book file PDF easily for everyone and every device. You can download and read online. SIEMENS HICOM E SERVICE MANUAL Pdf Download online Hicom E Telephone pdf manual download Also for Hicom Hicom.

Author: Akishicage Moogukus
Country: Sweden
Language: English (Spanish)
Genre: Software
Published (Last): 12 December 2009
Pages: 221
PDF File Size: 18.49 Mb
ePub File Size: 8.18 Mb
ISBN: 628-8-41574-643-7
Downloads: 34815
Price: Free* [*Free Regsitration Required]
Uploader: Vudolmaran

Generally speaking, the systems are not suit- able for a cable that exits the building. Page Classes of service Night service, enter ext. Figure Equipping sequence for the expansion box Page Initial operation Converting from SW 2. It does not illustrate the maximum configuration possible or authorization-related restrictions.

SIEMENS HICOM E SERVICE MANUAL Pdf Download.

Hicom has two slots that are used for line modules analogue servicehandbucch, S. Central call detail recording in Hicom is to be set to compressed output format, without recording incoming calls and without a On ringing. Setting A Dial Pause Route 1: The classes of service correspond to the values specified in the chapter “Classes of service as of SW 2.

Load the current extension numbers to Caracas Desk via the “Settings”, “Basic settings”, “Load customer data” menus. Page This procedure lasts approx. Line 6 shows how it can be set that all numbers beginning with the digits ” PC board connectors for the terminal blocks.

  JAN TROST KVALITATIVA INTERVJUER PDF

100f Simplified dialling OFF Status: The only difference is that an additional third expansion level 6 slots in total is provided in SW version 2.

Outgoing trunk traffic Pin assignment of the V. Contact assignment of the fax recognition and DDI module Caution Normally, W1 and W2 are always jumpered and the jumper must be inserted before initial operation.

Overview of modules Add-on modules for system expansions For Hicommodule cutover is dependent on the system code, i. The call numbers can be input in any servicehahdbuch.

Serial Interface Board sib v. Gone to lunch Change input An absence message can be deleted by pressing the F3 key under point F.

Siemens Hicom 100 E Service Manual

The existing LCR table containing 50 entries is used as an exception table servicehandbbuch Table 8- On the basis of the exception table, the system decides whether or not a call should be set up via the normal Telecom or corporate network.

Table Of Contents Codes for accessing services Select substitute code 79 Code: Untidiness at the workplace involves the risk of injuries. Page 81 Servicehaandbuch a call Although a call is signalled, the called extension can seize another line without answering the first call.

System Programming In Interactive Mode Simply follow the user prompts; the system will always inform you of available and unavailable error messages options and will recommend corrective measures using expert mode branch address to collision entry found.

Disable time, select sensor 1—4 and enter 0— Sensor name, select sensor 1—4, enter alphanumeric names max. Only use the original plug-in power supply unit.

  ELOXIEREN ANLEITUNG PDF

Page Unrestricted trunk ac- User may telephone without any restrictions cess Table Classes of service as of SW 2. Page – V. For each Hicom E extension, however, the tie line number and the relevant extension number hickm be entered as the direct dialling in number.

Page 10 m.

Page 45 servicehnadbuch Main module – motherboard Page 46 – Figure Motherboard interfaces as of The following values are possible: Digit Suppression Output incoming calls Output: The first step entails defining the planned option type as well as the number of modules. The signalling cycle is then increased to 10s intervals and the cyclical signals are maintained during the entire administration and maintenance procedure. Route Assignment Line 3: Diversion, External as Of Sw Version 2.

Headset Call pickup group 1 for ext. Resetting a call Although a call is signalled, the called extension can seize another line without answering the first call. In the case of mixed equipping, a distinction must be made between the routes. This contains information identifying the extension which made the call, for example, and whether the call was forwarded or transferred.

siemens_hicom_e_service_manual

The system activates analogue ports only after seizure. Reset PIN for ext. Defining The Call Duration Sensor no.